PERMASIL® High Visibility Disperse Dye

PERMASIL® High Visibility Disperse Dye

PERMASIL®
High Visibility Disperse Dye

Xenon Light Fastness

Wash Fastness 2A Stain

Sublimation (360°F/30 sec.) Stain

pH Range

Suitability for Atmospheric Dyeing (w/ Carrier)

Suitability for Thermosol Dyeing

Energy Level

PERMASIL®
Flavine 8GFF 1.0%

4

3-4

5

4-6

Limited

Not Suitable

Med

PERMASIL®
Flavine 10GN 400%
1.0%

5

5

5

4-6

Limited

Not Suitable

High

PERMASIL®
Luminous Pink

5B New

1.0%

5

5

2-3

4-6

Limited

Limited

Med

PERMASIL®
Luminous Red G

1.0%

4

4

4-5

4-6

Not Suitable

Suitable

High

PERMASIL®
Red SBN 200%

1.0%

6

5

5

4-6

Not Suitable

Limited

High

PERMASIL®
Blue

BG-GR 200%

1.0%

7-8

4-5

4

3-7

Suitable

Suitable

Med

Safety Red Combination

Safety Green Combination

1.3% PERMASIL® Flavine 8GFF

2.0% PERMASIL® Luminous Red G

1.0% PERMASIL® Flavine 10GN 400%

0.003% PERMASIL® Blue BG-GR 200%

Procedures:

Dyeing at 140º

Pre-scour with 1& STANSCOUR® BRC at 160º for 20-minutes.

  1. Drop & rinse.
  2. Set bath at 90ºF with:
    1. Xg/l salt (per chart below)
  3. Add PERMARBIL® Reactive Dye (pre-dissolve in 160º-180ºF water).
  4. Run 10-minutes.
  5. Add 1/10 total amount of Soda Ash over 10-minutes.
    1. Run 10-minutes.
  6. Add remaining 9/10 Soda Ash over 10-minutes (pH 10.8-11.2).
    1. Run 10-minutes.
  7. Heat to 140ºF at 2ºF/minute.
    1. Run for 45-minutes.
  8. Sample.
    1. If shade is acceptable, drop bath.
    2. When sampling shade, swatch should be: rinsed cold, rinsed warm, and neutralized with 0.25% Acetic Acid. Then, scoured at 200ºF – see steps 12-18.
  9. Rinse at 120ºF for 10-minutes.
    1. Drop bath.
  10. Rinse at 140º for 10-minutes.
    1. Drop bath.
  11. Neutralize at 120ºF with 0.25% Acetic Acid (pH 7-8).
    1. Run 10-minutes.
    2. Drop bath.
  12. Set fresh bath to 120ºF.
  13. Heat to 200ºF.
    1. Hold 10-minutes.
    2. Drop bath.
  14. Set bath to 120ºF.
    1. Hold 10-minutes.
    2. Drop bath.
  15. Finish as usual.

Salt and Soda Ash Recommendations for Cotton/Rayon

% Reactive Dye

g/l Sodium Chloride or Sodium Sulfate

g/l Soda Ash

0-0.25

30

5

0.26-0.50

50

5

0.51-1.00

60

10

1.01-2.00

60

10

2.01-3.00

80

10

3.01-5.00

80

10

Above 5.00*

*When dyeing above 5.00% the yield should increase with use of 100g/l salt

80-100

10

PERMABRIL® Brill Blue R Special Requires Reduced Salt

% Reactive Dye

g/l Sodium Chloride or Sodium Sulfate

up to 0.50

20

0.51-2.00

30

2.01-4.00

40

Above 4.00

50

Skip to content